Change font size   Print view

mark appears

Discussion board for Mackie's d8b Digital Console users.

Re: mark appears

Postby pino68 » Mon Aug 19, 2019 5:17 pm

do you think it's better to change the two batteries?
Error 43 can resolve?
pino68
Registered user
 
Posts: 152
Joined: Thu Aug 17, 2017 10:52 pm

Re: mark appears

Postby Phil.c » Mon Aug 19, 2019 5:22 pm

The batteries keep the CMOS settings correct, if your batteries haven't been changed for over two years then it's a good idea...you didn't answer my question about 48 and 44.1 settings?
User avatar
Phil.c
Premium Member
Premium Member
 
Posts: 1114
Joined: Sun Nov 23, 2008 10:58 pm
Location: South Wales

Re: mark appears

Postby pino68 » Mon Aug 19, 2019 5:25 pm

I tried to set 48 on both machines but it gave me problems, I also tried 44.1 but the problems continue ...
pino68
Registered user
 
Posts: 152
Joined: Thu Aug 17, 2017 10:52 pm

Re: mark appears

Postby Phil.c » Mon Aug 19, 2019 7:45 pm

If I were you, I would change the batteries, when you have the lids off, re-seat the ribbon connectors and any other connectors that you can see, but do it one at a time.
Re-check that you have all the cables connected right between HDR & D8b, clean and re-seat all the d8b cards, then boot up and check the CMOS, after that check the setups are correct, see where that gets you.
User avatar
Phil.c
Premium Member
Premium Member
 
Posts: 1114
Joined: Sun Nov 23, 2008 10:58 pm
Location: South Wales

Re: mark appears

Postby pino68 » Mon Aug 19, 2019 7:55 pm

did everything as you said, but nothing to do ... if I set the sample rate to 48, after I turn it off and on again it reposition itself to 44.1 (this in the D8B). In the HDR, on the other hand, it does the opposite, if it is set at 44.1 when it comes back up to 48 KHz
pino68
Registered user
 
Posts: 152
Joined: Thu Aug 17, 2017 10:52 pm

Re: mark appears

Postby Phil.c » Mon Aug 19, 2019 8:06 pm

??????
User avatar
Phil.c
Premium Member
Premium Member
 
Posts: 1114
Joined: Sun Nov 23, 2008 10:58 pm
Location: South Wales

Re: mark appears

Postby pino68 » Mon Aug 19, 2019 9:26 pm

Then:
1) I turn on the two machines, HDR and D8B.
2) I realize that the sample rate of the D8B is different from the HDR sample rate.
3) Imposed for the two values to be equal
4) I give the Play from the D8B but it remains completely still, nothing HDR nor the D8B starts.
5) I press the HDR Play and only HDR starts ... the D8B does not start.
6) I turn the machines off and on again ... the same thing always happens, the Sample Rates are different, they are not stored. (the batteries have been changed, so I don't think they are the batteries)

I wonder can it not be a software setup problem?
pino68
Registered user
 
Posts: 152
Joined: Thu Aug 17, 2017 10:52 pm

Re: mark appears

Postby Phil.c » Mon Aug 19, 2019 11:37 pm

OS might be your problem, re-load it
User avatar
Phil.c
Premium Member
Premium Member
 
Posts: 1114
Joined: Sun Nov 23, 2008 10:58 pm
Location: South Wales

Re: mark appears

Postby pino68 » Tue Aug 20, 2019 12:56 am

I wanted to ask you: if I reload my original OS, can I then install the cracked plugins?

If yes, where can I find the plugins?
pino68
Registered user
 
Posts: 152
Joined: Thu Aug 17, 2017 10:52 pm

Re: mark appears

Postby arjepsen » Tue Aug 20, 2019 2:11 pm

You can download the files that helps you make the installation floppy disks here:

OS 5.1:
http://www.sonido-7.com/d8b/files/OS/wi ... 5%20PC.zip

plugins:
http://www.sonido-7.com/d8b/files/OS/wi ... Pack_3.zip

After the installation, you can use this hack:
download/file.php?id=448

as far as I understand, you only have to replace the MackieOS.EXE in the d8b with the one in this zip file.
arjepsen
Premium Member
Premium Member
 
Posts: 603
Joined: Sun Nov 02, 2014 9:10 pm

PreviousNext

Return to d8b Forum

Who is online

Users browsing this forum: Google [Bot] and 27 guests

cron