Change font size   Print view

Mutec MC-3+ Smart Clock

Discussion board for Mackie's d8b Digital Console users.

Re: Mutec MC-3+ Smart Clock

Postby the boss » Thu Jan 15, 2015 10:05 pm

You have to use apogee clock cards in both your d8b's to get it right. The stock card can't recive any worldclock .
the boss
Registered user
 
Posts: 144
Joined: Fri Feb 07, 2014 6:45 pm

Re: Mutec MC-3+ Smart Clock

Postby Carlo » Fri Jan 16, 2015 9:06 am

Hi BOSS,

Thanks for your help. In fact both my d8b's are equipped with the APOGEE CLK cards and the method you mentioned earlier on works great for me. Money saved as well since now i dont need a clock generator thanks to you ;)

Best regards mate

Carlo
If I have seen further it is only by standing on the shoulders of giants........
User avatar
Carlo
Premium Member
Premium Member
 
Posts: 431
Joined: Sat Jan 15, 2011 11:40 pm
Location: EU

Re: Mutec MC-3+ Smart Clock

Postby the boss » Fri Jan 16, 2015 1:16 pm

Rock n roll :)
the boss
Registered user
 
Posts: 144
Joined: Fri Feb 07, 2014 6:45 pm

Re: Mutec MC-3+ Smart Clock

Postby Carlo » Wed Jul 08, 2015 7:53 am

the boss wrote:Hi

You don't need this device to connect this things together.
I have 2 d8b's with 4 x motu 2408 mk3 and a motu mtp.

You need two apogee sync card.

1 set your daw as master.
2 connect your first d8b sync in on apogee card to sync out on your motu card.
3 set first d8b to word clock in.
4 connect first d8b word clock out to apogee world clock in on d8b 2.
5 set d8b 2 to worldclock in.
Set your d8b's to sync sample rates in options.
REMEMBER to always boot up your d8b's first.
After fully boot start the motu interface.

Good luck ;)



Hey Boss,

IT works! but i have an issue. On my second d8b i have an OPT8 - DIO8 - DIO8 cards configuration. On the first bank the sync seems ok but on the 2nd and 3rd bank i get a popping sound and an infrequent peak signal on the meter bridge. Is it possible that the DIO8 is not getting enough sync? Shall i swap them with other OPT8 cards? My first d8b has 3x OPT8 cards. I was going to change 2 of them with the 2nd d8b DIO8's. What do you think pls?

Carlo
If I have seen further it is only by standing on the shoulders of giants........
User avatar
Carlo
Premium Member
Premium Member
 
Posts: 431
Joined: Sat Jan 15, 2011 11:40 pm
Location: EU

Re: Mutec MC-3+ Smart Clock

Postby the boss » Wed Jul 08, 2015 10:42 pm

Hi

Check your opto cables.... This is not a stabil connection type. Just re connect or try others.
the boss
Registered user
 
Posts: 144
Joined: Fri Feb 07, 2014 6:45 pm

Re: Mutec MC-3+ Smart Clock

Postby the boss » Wed Jul 08, 2015 10:47 pm

.... Do not use too long opto cables and do not bend. Remember it's opto... If you can use tdif format... :)
the boss
Registered user
 
Posts: 144
Joined: Fri Feb 07, 2014 6:45 pm

Re: Mutec MC-3+ Smart Clock

Postby Carlo » Thu Jul 09, 2015 1:04 pm

Thanks so much
If I have seen further it is only by standing on the shoulders of giants........
User avatar
Carlo
Premium Member
Premium Member
 
Posts: 431
Joined: Sat Jan 15, 2011 11:40 pm
Location: EU

Re: Mutec MC-3+ Smart Clock

Postby anyhorizon » Thu Jul 09, 2015 8:19 pm

the boss wrote:.... Do not use too long opto cables and do not bend. Remember it's opto... If you can use tdif format... :)


I find that a strange comment. The data travels at the speed of light. You'd be hard pressed to be worried about the length of the cable... and they are surprisingly flexible.

Peter
In the scheme of things, there isn't one... just chaos.
User avatar
anyhorizon
Premium Member
Premium Member
 
Posts: 1069
Joined: Fri Nov 21, 2008 9:36 pm
Location: Down under or up over, depending on where in space you are.

Re: Mutec MC-3+ Smart Clock

Postby hyaena » Thu Jul 09, 2015 11:23 pm

Hi Peter,

nice to read you posting.
Any chance to get another song like "Rainy Night Again" from you ?
There´s no such forum for the DM2000, that I´m on now and so I come back from time to time - became addicted, I think.

So, have a good time

Manfred.
User avatar
hyaena
Premium Member
Premium Member
 
Posts: 79
Joined: Tue Jan 18, 2011 1:20 am
Location: Bietigheim-Bissingen, Germany

Re: Mutec MC-3+ Smart Clock

Postby garrett21allen » Fri Jul 10, 2015 5:10 am

I have been hopping peter would do another song
he has a power house voice coming out of that little body
now peter I am not saying you are little. what I mean is
the last song you put out I ask you a few things about how you
you did the reverb. you worlds to me was that's just little old me singing
I would love to hear another song from you. but I fill like you got a lot going on
maybe one day you will do another one for us old timers

Joe Allen
garrett21allen
Premium Member
Premium Member
 
Posts: 517
Joined: Wed Feb 04, 2009 5:54 pm

PreviousNext

Return to d8b Forum

Who is online

Users browsing this forum: No registered users and 0 guests